D-Link DI-308 Instrukcja Użytkownika Strona 61
- Strona / 131
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
DI-308 ISDN Remote Router
53
•
State –
This is used to define the routing decision applied to the packet. The
three routing decisions are described:
1.
Forward
–
This allows the routing of the packet, if it has met the criteria of
the corresponding filter.
2.
Drop
–
This drops (doesn’t allow routing for) a specific packet that has met
the criteria of the corresponding filter.
3.
Disable
–
This does not apply the IP filter.
•
Interface –
This applies the filter to a specific interface, LAN or one of the ISDN
interfaces.
•
Protocol Type –
This is a protocol identifier, as assigned by the Internet
Assigned Numbers Authority (IANA). The values of this identifier are described
in RFC-1700. This router supports the following:
1
- This is Internet Control Message (ICMP), defined in RFC 792.
6
- This is Transmission Control (TCP), defined in RFC 793.
17
- This is User Datagram (UDP), defined in RFC 798.
•
Src IP –
This is the source address in the IP header of this packet.
•
Src Netmask –
This mask is bit-wise AND’d with the source IP address and bit-
wise AND’d with the IP address of the incoming interface. The two results are
then compared.
•
Src Port –
This is the source port, in the TCP or UDP header, of the packet.
•
Src Port Operation –
This comparison operation is applied to the source port
(the Src Port parameter) value, of the TCP or UDP header.
•
Dst IP –
This is the destination address in the IP header of the packet.
•
Dst Netmask –
This mask is bit-wise AND’d with the destination IP address and
bit-wise AND’d with the IP address of the incoming interface. The two results are
then compared.
•
Dst Port –
This is the destination port, in the TCP or UDP header, of the packet.
•
Dst Port Operation –
This comparison operation is applied to the destination
port (the Dst
Port parameter) value, of the TCP or UDP header.
•
ICMP Type –
This is the type field, in the ICMP header, used to identify a
particular ICMP message.
•
ICMP Code –
This is the code field, in the ICMP header, used to further specify
the ICMP type.
•
TCP Flag –
This is a hex number, representing the six flag bits in the TCP
header. The value range is from 0 to 3F.
- ISDN Router 1
- User’s Guide 1
- Copyright Statement 2
- Trademarks 2
- Limited Warranty 3
- Wichtige Sicherheitshinweise 4
- Table of Contents 5
- Introduction 9
- DI-308 ISDN Remote Router 10
- Applications for your DI-308 11
- What This Manual Covers 11
- Other Resources 13
- Packing List 13
- Installation 14
- The DI-308 Rear Panel 15
- Telephone Features 16
- Configuration and Management 24
- System Information 25
- Interface Configuration 26
- Network Configuration 29
- SNMP Agent Configuration 35
- Advanced Functions 38
- Dial-In User Connections 40
- Remote Network Connections 40
- Dial-In Network Connections 40
- Dial-Out Network Connections 41
- Dial In IP Pool 43
- ISDN Link 1 44
- IP Address 66
- A 10.0.0.0 10.255.255.255 68
- B 172.16.0.0 172.31.255.255 68
- C 192.168.0.0 192.168.255.255 68
- Admin Configuration 83
- System Maintenance 83
- Diagnostic 96
- Connection Test 96
- PROM System Configuration 106
- Using Telnet 112
- Using RADIUS Authentication 114
- Appendix A - Troubleshooting 116
- Appendix B - IP Concepts 118
- Subnet Mask 119
- IP Protocol Numbers 120
- IP Port Numbers 120
- Physical & Environmental 121
- Configuration File Example 124
- Offices 129
- Registration Card 130
Powiązane produkty i podręczniki dla Urządzenia dostępowe ISDN D-Link DI-308
(119 strony)Sony Ericsson W395(W395) manuály
Uživatelské manuály a uživatelské příručky pro Mobilní telefony Sony Ericsson W395(W395).
Poskytujeme 1 manuály pdf Sony Ericsson W395(W395) ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Komentarze do niniejszej Instrukcji