D-Link DSS-24+ Podręcznik Użytkownika

DSS-8+ 8-port 10/100Mbps Switch User’s Guide Rev. 03 (MAR. 2001) 6012-9830016 Printed In Taiwan RECYCLABLE

7 IDENTIFYING EXTERNAL COMPONENTS This section identifies all the major external components of the DSS-8+. Both the front and rear panels are shown

8 duplex (FDX) mode. Otherwise, it is blinking when collisions are occurring on the respective port. 100M Link/Activity, 10M Link/Activity (100M LIN

9 another hub or an Ethernet switch, you should use a crossover cable, or make the connection using the MDI-X jack (described below). ♦ Uplink Jack(s

10 CONNECTING THE DSS-8+ This chapter describes how to connect the DSS-8+ to your Fast Ethernet network. In each of the following figures, the DSS-8

11 A. 10BASE-T Hub For a 10BASE-T hub, the DSS-8+ LED indicators should light up as the following: “Full-Duplex/Collision” indicator is OFF. “100LI

12 A. Using straight cable When using straight cable, this is done from the uplink (MDI-II) port of the DSS-8+ (DSS-8+ A) to any of the 10Mbps or 10

INSTRUCTIONS FOR USE OF STACKING BRACKETS First, make sure you have one pair of stacking brackets for each device. Next, slide one bracket onto each

14 RJ-45 PIN SPECIFICATION When connecting your DSS-8+ to another switch, a bridge or a hub, a modified crossover cable is necessary. Please review

15 The standard RJ-45 receptacle/connector The following shows straight cable and crossover cable connection: Straight cable for DSS-8+ (upl

16TECHNICAL SPECIFICATIONS General Standards IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet ANSI/IEEE Std. 802.3 NWay Auto-nego

i TABLE OF CONTENTS ABOUT THIS GUIDE...1 PURPOSE ...

17Physical and Environmental DC inputs DC7.5V/1.5A Power Consumption 11.25 watts. (max.) Temperature Operating: 0° ~ 50° C, Storage: -10° ~ 70° C

FCC Certifications This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC R

LIMITED WARRANTY D-Link provides this limited warranty for its product only to the person or entity who originally purchased the product from D-Link

Limited Software Warranty: D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current

Office and, if requested, provide written proof of purchase of the product (such as a copy of the dated purchase invoice for the product) before the

FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION

Trademarks Copyright 1999 D-Link Corporation. Contents subject to change without prior notice. D-Link is a registered trademark of D-Link Corpora

ii DSS-8+ TO SWITCH (OTHER DEVICES)...11 A. Using straight cable...

1 ABOUT THIS GUIDE Congratulations on your purchase of the DSS-8+. This device integrates 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilit

2 INTRODUCTION This chapter describes the features of the DSS-8+ and some background information about Ethernet/Fast Ethernet switching technology. F

3 Ethernet packets at the MAC address level of the Ethernet protocol transmitting among connected Ethernet or Fast Ethernet LAN segments. Switching i

4 Features The DSS-8+ was designed for easy installation and high performance in an environment where traffic on the network and the number of users

5  Store and forward switching scheme capability. As the result of complete frame checking and error frame filtering, this scheme prevents error p

6 Unpacking and Setup This chapter provides unpacking and setup information for the DSS-8+. Unpacking Open the box and carefully unpacks its contents